oil pump

1. Fit cover plate for oil pump drive using three screws.
   使用三个螺钉安装机油泵驱动装置的盖板。
2. With thickening oil-tank cover-board, it makes acting noise of oil pump and solenoid valve smaller.
   加厚的油箱盖板使油泵和电磁阀的动作噪音更小。
3. It adopts gear oil pump set, oil supply stable and has low noise.
   采用齿轮油泵组，供油稳定、澡音低。
4. The reducer unit is a reducer, a high pressure oil pump or a hydraulic motor.
   减速机构为减速机、或高压油泵和液压马达。
5. Two more chains drive the oil pump and the two high-pressure pumps actuate the common rail injection system.
   另外两个链条驱动机油泵和两个高压泵开动的共轨喷射系统。
6. Connect oil pump to roll journal.
   连接油泵与辊颈。
7. According to the oil pump use characteristics of the pump flow requirements of the surface have sufficient wear resistance;
   根据油浆泵使用特点，要求泵的过流件表面要有足够的耐磨性；
8. The oil pump drive should be examined if the oil pressure is low.
   如果机油压力过低，则应检查机油泵驱动装置。
9. A lubricating oil pump shaft and a cam transmission shaft are respectively sheathed in series in two inner cavities.
   两内腔内分别串套机油泵轴和凸轮传动轴。
10. Operation test of emergency switching-off device for oil pump and ventilator ( bilge pump) in engine room.
    机舱风、油（舱底泵）应急切断装置操作试验。
11. Grease the sealing rings on the transmission oil pump with liqui-moly for example.
    润滑（例如用liqui-moly）变速器油泵上的密封圈。
12. Fit guide rail and tensioning rail for the oil pump drive.
    安装机油泵驱动装置的导轨和张紧轨。
13. It drives the camshaft roller-type chain and the oil pump via a sprocket.
    它通过链轮驱动凸轮轴滚柱型链条和机油泵。
14. In the engineering industry as hydraulic and lubricating oil pump.
    在机械工业中用做液压以及润滑泵。
15. The center motor drives the fuel pump and the small one at the right the oil pump.
    该中心电机驱动器的燃料泵和在适当的油泵小之一。
16. Analysis of Oil Pump Rotor Based on Pro/ E and ANSYS
    基于Pro/E和ANSYS的油泵转子分析
17. The utility model also can effectively avoid engine oil bubble to improve the efficiency of the engine oil pump.
    本实用新型还可以有效避免出现机油气泡，使机油泵效率升高。
18. Oil pump drive chain sprocket is pressed onto the front of the crankshaft.
    油泵驱动链轮上按下了曲轴的前面。
19. A Discussion on Matching Design of Motor and Oil Pump of POL Equipment
    油料装备中发动机与油泵的匹配设计探讨
20. Lubricating oil and piston cooling oil pump
    润滑油及活塞冷却油泵
21. To do this, fix the oil pump on the stud bolts of the engine engine carrier.
    要完成此操作，请将机油泵安装在发动机托架的双头螺栓上。
22. To fit inline type high pressure oil pump.
    与转子式高压油泵匹配。
23. Main products: oil tank, oil tube, oiler support, oil pump, oil applying wheel etc.
    产品主要结构：油箱、油管、安装支架、油泵总成及涂油轮等组成。
24. Applying mass flow oil pump guarantees the reliability of the lubricating system.
    采用大流量机油泵，确保润滑系统稳定可靠。
25. Analysis and elimination of a fault at the gland of compensating oil pump for diaphragm compressor
    隔膜压缩机补偿油泵压盖被顶起的故障分析和排除
26. External motor and oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.
    由于电机、油泵外置，其通风冷却条件好，运行安全，寿命长。
27. Burning fuels such as coal and oil pump vast amounts of greenhouse gases into the atmosphere.
    燃烧煤炭和石油这类化石燃料会产生大量的温室气体。
28. Tighten three screws on the oil pump.
    拧紧机油泵上的三个螺钉。
29. Connect oil pump and joining socket together.
    将机油泵和连接套连接在一起。
30. First of all, compressor lubrication oil pump is usually composed of spindle drive of the compressor.
    首先，压缩机润滑油泵通常是由压缩机主轴驱动的。

noun

1. a pump that keeps a supply of oil on moving parts